Investigation of the rheology and strength of geopolymer mixtures for extrusion-based 3D printing

Khoshnevis, 2004, Automated construction by contour crafting—related robotics and information technologies, Autom. ConStruct., 13, 5, 10.1016/j.autcon.2003.08.012 Tay, 2017, 3D printing trends in building and construction industry: a review, Virtual Phys. Prototyp., 1–16, 261, 10.1080/17452759.2017.1326724 Paul, 2018, Fresh and hardened properties of 3D printable cementitious materials for building and construction, Arch. Civil.Mech. Eng., 18, 311, 10.1016/j.acme.2017.02.008 Le, 2012, Hardened properties of high-performance printing concrete, Cement Concr. Res., 42, 558, 10.1016/j.cemconres.2011.12.003 Franchin, 2017, Direct ink writing of geopolymeric inks, J. Eur. Ceram. Soc., 37, 2481, 10.1016/j.jeurceramsoc.2017.01.030 Khoshnevis, 2016, Construction by contour crafting using sulphur concrete with planetary applications, Rapid Prototyp. J., 22, 848, 10.1108/RPJ-11-2015-0165 Le, 2012, Mix design and fresh properties for high-performance printing concrete, Mater. Struct., 45, 1221, 10.1617/s11527-012-9828-z Perrot, 2016, Structural built-up of cement-based materials used for 3D-printing extrusion techniques, Mater. Struct., 49, 1213, 10.1617/s11527-015-0571-0 Panda, 2017, Additive manufacturing of geopolymer for sustainable built environment, J. Clean. Prod., 167, 281, 10.1016/j.jclepro.2017.08.165 Xia, 2016, Method of formulating geopolymer for 3D printing for construction applications, Mater. Des., 110, 382, 10.1016/j.matdes.2016.07.136 Cornell, 2002 Ruiz-Santaquiteria, 2012, Alkaline solution/binder ratio as a determining factor in the alkaline activation of aluminosilicates, Cement Concr. Res., 42, 1242, 10.1016/j.cemconres.2012.05.019 Ouyang, 2016, The thixotropic behavior of fresh cement asphalt emulsion paste, Construct. Build. Mater., 114, 906, 10.1016/j.conbuildmat.2016.04.024 Hasanzadeh, 2017 Khayat, 2012, Field-oriented test methods to evaluate structural build-up at rest of flowable mortar and concrete, Mater. Struct., 45, 1547, 10.1617/s11527-012-9856-8 Li, 2017, 3D bioprinting of highly thixotropic alginate/methylcellulose hydrogel with strong interface bonding, ACS Appl. Mater. Interfaces, 9, 20086, 10.1021/acsami.7b04216 Panda, 2018, Experimental study on mix proportion and fresh properties of fly ash based geopolymer for 3D concrete printing, Ceram. Int., 44, 10258, 10.1016/j.ceramint.2018.03.031 Panda, 2018, Measurement of tensile bond strength of 3D printed geopolymer mortar, Measurement, 113, 108, 10.1016/j.measurement.2017.08.051 ASTM C1702-15a, 2015, 8 BS EN 196-1, 2016 Favier, 2014, Flow properties of MK-based geopolymer pastes. A comparative study with standard Portland cement pastes, Soft Matter, 10, 1134, 10.1039/c3sm51889b Memon, 2013, Effect of silica fume on the fresh and hardened properties of fly ash-based self-compacting geopolymer concrete, International Journal of Minerals, Metallurgy and Materials, 20, 205, 10.1007/s12613-013-0714-7 Feys, 2009 Saha, 2017, Enhancement of the properties of fly ash based geopolymer paste by incorporating ground granulated blast furnace slag, Construct. Build. Mater., 146, 615, 10.1016/j.conbuildmat.2017.04.139 Roussel, 2012, The origins of thixotropy of fresh cement pastes, Cement Concr. Res., 42, 148, 10.1016/j.cemconres.2011.09.004 2011 Salem, 2002, Electrical conductivity and rheological properties of ordinary Portland cement–silica fume and calcium hydroxide–silica fume pastes, Cement Concr. Res., 32, 1473, 10.1016/S0008-8846(02)00809-8 Assaad, 2003, Assessment of thixotropy of flowable and self-consolidating concrete, Materials Journal, 100, 99 Bernal, 2011, Evolution of binder structure in sodium silicate-activated slag-metakaolin blends, Cement Concr. Compos., 33, 46, 10.1016/j.cemconcomp.2010.09.004 Temuujin, 2009, Influence of calcium compounds on the mechanical properties of fly ash geopolymer pastes, J. Hazard Mater., 167, 82, 10.1016/j.jhazmat.2008.12.121 Panda, 2017, Anisotropic mechanical performance of 3D printed fiber reinforced sustainable construction material, Mater. Lett., 209, 146, 10.1016/j.matlet.2017.07.123 Roussel, 2018, Rheological requirements for printable concretes, Cement Concr. Res., 112, 76, 10.1016/j.cemconres.2018.04.005 Reiter, 2018, The role of early age structural build-up in digital fabrication with concrete, Cement Concr. Res., 112, 86, 10.1016/j.cemconres.2018.05.011 Roussel, 2010, Steady state flow of cement suspensions: a micromechanical state of the art, Cement Concr. Res., 40, 77, 10.1016/j.cemconres.2009.08.026 Roussel, 2006, A thixotropy model for fresh fluid concretes: theory, validation and applications, Cement Concr. Res., 36, 1797, 10.1016/j.cemconres.2006.05.025 Ma, 2018, Mechanical characterization of 3D-printed anisotropic cementitious material by the electromechanical transducer, Smart Mater. Struct., 27, 075036, 10.1088/1361-665X/aac789