Heat treatment of Ti‐6Al‐7Nb components produced by selective laser melting

Emerald - 2008
TimSercombe1, NoelJones2, RobDay3, AlanKop3
1The University of Western Australia, Perth, Australia
2Australian Synchrotron Company, Melbourne, Australia
3Royal Perth Hospital, Perth, Australia

Tóm tắt

PurposeThe purpose of this paper is to describe a preliminary investigation into the heat treatment of Ti‐6Al‐7Nb components that had been produced via selective laser melting (SLM).Design/methodology/approachBars of Ti‐6Al‐7Nb were produced using SLM by MCP‐HEK Tooling GmbH in Lubeck, Germany. These bars were then subjected to a range of heat treatments and the resultant microstructure evaluated with respect to its likely effect on fatigue.FindingsIt was found that the as received material consisted of an α′ martensitic structure in a metastable β matrix. Evidence of the layer‐wise thermal history was present, as were large (up to ∼500 μm) pores. Solution treatment at 955°C (below the β transus) did not completely disrupt this layered structure and is therefore not recommended. When solution treatment was performed at 1,055°C (above the β transus) a homogeneous structure was produced, with a morphology that depended on the post‐solution treatment cooling rate. It was concluded that the most promising heat treatment consisted of a moderate cooling rate after solution treatment at 1,055°C.Research limitations/implicationsThe study had only limited material and therefore it was not possible to perform any mechanical property testing.Practical implicationsThe paper presents the initial findings of a project which is aimed at optimising the mechanical properties of Ti‐6Al‐7Nb components produced using SLM.Originality/valueCurrently, little is known about the heat treatment and subsequent mechanical properties of this Ti‐6Al‐7Nb alloy when produced using rapid manufacturing techniques. Such lack of knowledge limits the potential applications, especially in the biomedical field where the consequences of implant failure are high. The paper presents the first step in developing this understanding.

Từ khóa


Tài liệu tham khảo

Berry, D.J., Lewallen, D.G., Hanssen, A.D. and Cabanela, M.E. (1999), “Pelvic discontinuity in revision total hip arthroplasty”, J. Bone Joint Surg. Am., Vol. 81 No. 1, pp. 692‐702.

Christie, M.J., Barrington, S.A., Brinson, M.F., Ruhling, M.E. and DeBoer, D.K. (2001), “Bridging massive acetabular defects with the triflange cup: 2‐ to 9‐year results”, Clinical Orthopaedics and Related Research, Vol. 393, pp. 216‐27.

Collings, E.W. (1984), The Physical Metallurgy of Titanium Alloys, American Society for Metals, Metals Park, OH.

Dennis, D.A. (2003), “Management of massive acetabular defects in revision total hip arthroplasty”, J. Arthroplasty, Vol. 18 No. 3, supplement 1, pp. 121‐5.

Eylon, D., Barice, W.J. and Froes, F.H. (1985), “Overcoming material boundries”, 17th National SAMPE Technical Conference, pp. 585‐95.

Gilbert, R. and Shannon, R. (1991), “Titanium. A technical guide”, in ASM Handbook Volume 4, Heat Treatment, ASM International, Materials Park, OH.

Holt, G.E. and Dennis, D.A. (2004), “Use of custom triflanged acetabular components in revision total hip arthroplasty”, Clinical Orthopaedics and Related Research, Vol. 429, pp. 209‐14.

Lutjering, G. (1998), “Influence of processing on microstructure and mechanical properties of (¦Á + ¦Â) titanium alloys”, Materials Science & Engineering A, Vol. 243, pp. 32‐45.

Santos, E.C., Shiomi, M., Osakada, K. and Laoui, T. (2006), “Rapid manufacturing of metal components by laser forming”, International Journal of Machine Tools & Manufacture, Vol. 46, pp. 1459‐68.

Sporer, S.M., O'Rourke, M. and Paprosky, W.G. (2005), “The treatment of pelvic discontinuity during acetabular revision”, The Journal of Arthroplasty, Vol. 20, pp. 79‐84.

Thông tin
Thông tin xuất bản

Emerald

Thông tin tác giả