Role of Thermal Spray Coatings on Erosion, Corrosion, and Oxidation in Various Applications: A Review

Journal of Bio- and Tribo-Corrosion - Tập 10 - Trang 1-17 - 2024
S. Suresh Kumar1,2, C. Durga Prasad1,2, Harish Hanumanthappa1,2
1Department of Mechanical Engineering, RV Institute of Technology and Management, Bengaluru, India
2Visvesvaraya Technological University, Belagavi, India

Tóm tắt

Depending on the location, extreme environmental conditions must have different graded properties. This is especially important for surfaces that are exposed to mechanical, chemical, thermal, and electrochemical interactions, as these can harm other components in use, such as gas turbines, ball valves, aerospace, power plants, and heat exchangers. The primary problems, such as oxidation, corrosion, erosion, and wear or their combinations will shorten the components life. One of the key deposition methods to address the said issues is thermal spray procedure. Amongst the several thermal spray approaches, the high-velocity oxy-fuel (HVOF) thermal spray technique is frequently used because of its improved performance, cheap expansion costs, and creation of high-density coatings with nominal porosity. In addition to discussing different coating materials and applications, this article provides an overview of advantages and limits of the HVOF spray method. This paper also addresses the impact of varying coating parameters on material significances relating to high-temperature performances, microstructural properties of HVOF spray technique, and electrochemical behaviours.

Tài liệu tham khảo

Praveen AS, Arjunan A (2022) High-temperature oxidation and erosion of HVOF sprayed NiCrSiB/Al2O3 and NiCrSiB/WCCo coatings. Appl Surf Sci Adv 7:100191 Doleker KM, Ozgurluk Y, Kahraman Y, Karaoglanli AC (2021) Oxidation and hot corrosion resistance of HVOF/EB-PVD thermal barrier coating system. Surf Coat Technol 409:126862 Sadeghi E, Joshi S (2019) Chlorine-induced high-temperature corrosion and erosion-corrosion of HVAF and HVOF-sprayed amorphous Fe-based coatings. Surf Coat Technol 371:20–35 Picas JA, Punset M, Rupérez E, Menargues S, Martin E, Baile MT (2019) Corrosion mechanism of HVOF thermal sprayed WC-CoCr coatings in acidic chloride media. Surf Coat Technol 371:378–388 Abu-Warda N, López AJ, López MD, Utrilla MV (2020) Ni20Cr coating on T24 steel pipes by HVOF thermal spray for high temperature protection. Surf Coat Technol 381:125133 Pradeep DG, Venkatesh CV, Nithin HS (2022) Review on tribological and mechanical behavior in HVOF thermal-sprayed composite coatings. J Bio Tribo Corros 8:30. https://doi.org/10.1007/s40735-022-00631-x Avci A, Eker AA, Eker B (2018) Microstructure and oxidation behavior of atmospheric plasma-sprayed thermal barrier coatings. Exergetic, energetic and environmental dimensions. Academic Press, Elsevier, pp 793–814 Sahith MS, Giridhara G, Suresh Kumar R (2018) Development and analysis of thermal barrier coatings on gas turbine blades–a review. Mater Today: Proceed 5(1):2746–2751 Demirci M, Bagci M (2022) Erosion of ceramic coating applications under the influence of APS and HVOF methods. Appl Nanosci 12(11):3409–3415 Suresh Babu P, Madhavi Y, Rama Krishna L, Sivakumar G, Srinivasa Rao D, Padmanabham G (2020) Thermal spray coatings for erosion–corrosion resistant applications. Trans Ind Inst Metals 73:2141–2159 Bolelli G, Bursi M, Lusvarghi L, Manfredini T, Matikainen V, Rigon R, Sassatelli P, Vuoristo P (2018) Tribology of FeVCrC coatings deposited by HVOF and HVAF thermal spray processes. Wear 394:113–133 Hajare AS, Gogte CL (2018) Comparative study of wear behaviour of Thermal Spray HVOF coating on 304 SS. Mater Today: Proceed 5(2):6924–6933 Singh S, Kumar R, Goel P, Singh H (2022) Analysis of wear and hardness during surface hardfacing of alloy steel by thermal spraying, electric arc and TIG welding. Mater Today: Proceed 50:1599–1605 Kumar S, Kumar R (2021) Influence of processing conditions on the properties of thermal sprayed coating: a review. Surf Eng 37(11):1339–1372 Song Bo, Murray JW, Wellman RG, Pala Z, Hussain T (2020) Dry sliding wear behaviour of HVOF thermal sprayed WC-Co-Cr and WC-CrxCy-Ni coatings. Wear 442:203114 Ham GS, Kreethi R, Kim HJ, Yoon SH, Lee KA (2021) Effects of different HVOF thermal sprayed cermet coatings on tensile and fatigue properties of AISI 1045 steel. J Mater Res Technol 15:6647–6658 Tillmann W, Kuhnt S, Baumann IT, Kalka A, Becker-Emden EC, Brinkhoff A (2022) Statistical comparison of processing different powder feedstock in an HVOF thermal spray process. J Therm Spray Technol 31(5):1476–1489 Seraj RA, Abdollah-zadeh A, Dosta S, Assadi H, Cano IG (2019) Comparison of stellite coatings on low carbon steel produced by CGS and HVOF spraying. Surf Coat Technol 372:299–311 Mittal G, Paul S (2022) Suspension and solution precursor plasma and HVOF spray: A review. J Therm Spray Technol 31(5):1443–1475 Murariu AC, Pleşu N, Perianu IA (2017) Investigations on corrosion behaviour of WC–CrC–Ni coatings deposited by HVOF thermal spraying process. Int J Electrochem Sci 12(2):1535–1549 Gui M, Eybel R, Radhakrishnan S, Monerie-Moulin F, Raininger R, Taylor P (2019) Residual stress in HVOF thermally sprayed WC-10Co-4Cr coating in landing gear application. J Therm Spray Technol 28(6):1295–1307 Kiilakoski J, Trache R, Björklund S, Joshi S, Vuoristo P (2019) Process parameter impact on suspension-HVOF-sprayed Cr2O3 coatings. J Therm Spray Technol 28:1933–1944 Pukasiewicz AGM, De Boer HE, Sucharski GB, Vaz RF, Procopiak LAJ (2017) The influence of HVOF spraying parameters on the microstructure, residual stress and cavitation resistance of FeMnCrSi coatings. Surf Coat Technol 327:158–166 Rajendran PR, Duraisamy T, Seshadri RC, Mohankumar A, Ranganathan S, Balachandran G, Murugan K, Renjith L (2022) Optimisation of HVOF spray process parameters to achieve minimum porosity and maximum hardness in WC-10Ni-5Cr coatings. Coatings 12(3):339 Srinath MK, Nagendra J (2022) Post-processing parameter optimization to enhance the surface finish of HVOF-developed coatings. Multiscale Multidiscip Model, Exp Des 5(3):255–267 Rukhande SW, Rathod WS (2020) Tribological behaviour of plasma and HVOF-sprayed NiCrSiBFe coatings. Surf Eng 36(7):745–755 Schab JC, Zimmermann JRA, Grasso P-D, Stankowski A, Heinze S, Marquardt A, Leyens C (2019) Thermodynamic calculation and experimental analysis of critical phase transformations in HVOF-sprayed NiCrAlY-coating alloys. Surf Coat Technol 357:924–938 Ghadami F, . Sabour Rouh Aghdam A (2020) Preparation of NiCrAlY/nano-CeO2 powder with the core-shell structure using high-velocity oxy-fuel spraying process. Mater Chem Phys 243:122551 Garcia-Segura S, Ocon JD, Chong MNan (2018) Electrochemical oxidation remediation of real wastewater effluents—A review. Process Saf Environ Prot 113:48–67 Galedari SA, Mahdavi A, Azarmi F, Huang Y, McDonald A (2019) A comprehensive review of corrosion resistance of thermally-sprayed and thermally-diffused protective coatings on steel structures. J Therm Spray Technol 28:645–677 Santos D, Jhones A, Garcia-Segura S, Dosta S, Cano IG, Martínez-Huitle CA, Brillas E (2019) A ceramic electrode of ZrO2-Y2O3 for the generation of oxidant species in anodic oxidation. Assessment of the treatment of Acid Blue 29 dye in sulfate and chloride media. Sep Purif Technol 228:115747 Ajayi BP, Thapa AK, Cvelbar U, Jasinski JB, Sunkara MK (2017) Atmospheric plasma spray pyrolysis of lithiated nickel-manganese-cobalt oxides for cathodes in lithium ion batteries. Chem Eng Sci 174:302–310 Waluyo NS, Park SS, Song RH, Lee SB, Lim TH, Hong JE, Ryu KH, Im WB, Lee JW (2018) Protective coating based on manganese–copper oxide for solid oxide fuel cell interconnects: plasma spray coating and performance evaluation. Ceram Int 44(10):11576–11581 Shestakova M, Sillanpää M (2017) Electrode materials used for electrochemical oxidation of organic compounds in wastewater. Rev Environ Sci Bio/Technol 16:223–238 Zhu Y, Zuwei Xu, Yan K, Zhao H, Zhang J (2017) One-step synthesis of CuO–Cu2O heterojunction by flame spray pyrolysis for cathodic photo electrochemical sensing of l-cysteine. ACS Appl Mater Interfaces 9(46):40452–40460 Wu J, Zhang SD, Sun WH, Wang JQ (2018) Influence of oxidation related structural defects on localized corrosion in HVAF-sprayed Fe-based metallic coatings. Surf Coat Technol 335:205–218 Chen Y, Zhao X, Xiao P (2018) Effect of microstructure on early oxidation of MCrAlY coatings. Acta Mater 159:150–162 Han Y, Zhu Z, Zhang B, Chu Y, Zhang Y, Fan J (2018) Effects of process parameters of vacuum pre-oxidation on the microstructural evolution of CoCrAlY coating deposited by HVOF. J Alloys Compds 735:547–559 Kalush A, Texier D, Ecochard M, Sirvin Q, Choquet K, Gheno T, Vanderesse N, Jomaa W, Bocher P (2022) Size effects on high temperature oxidation of MCrAlY coatings processed via APS and HVOF depositions. Surf Coat Technol 440:128483 Karaoglanli AC, Ozgurluk Y, Doleker KM (2020) Comparison of microstructure and oxidation behavior of CoNiCrAlY coatings produced by APS, SSAPS, D-gun, HVOF and CGDS techniques. Vacuum 180:109609 Fan L, Zhu B, Pei-Chen Su, He C (2018) Nanomaterials and technologies for low temperature solid oxide fuel cells: recent advances, challenges and opportunities. Nano Energy 45:148–176 Song B, Bai M, Voisey KT, Hussain T (2017) Role of oxides and porosity on high-temperature oxidation of liquid-fueled HVOF thermal-sprayed Ni50Cr coatings. J Therm Spray Technol 26:554–568 Hao E, Zhao X, An Y, Deng W, Zhou H, Chen J (2019) The effect of pre-oxidation on microstructure, mechanical properties and high-temperature tribological behaviors of HVOF-sprayed NiCoCrAlYTa coating. Appl Surf Sci 489:187–197 Feizabadi A, Salehi Doolabi M, Sadrnezhaad SK, Rezaei M (2018) Cyclic oxidation characteristics of HVOF thermal-sprayed NiCoCrAlY and CoNiCrAlY coatings at 1000° C. J Alloys Compds 746:509–519 Reddy NC, Ajay Kumar BS, Reddappa HN, Ramesh MR, Koppad PG, Kord S (2018) HVOF sprayed Ni3Ti and Ni3Ti+ (Cr3C2+ 20NiCr) coatings: Microstructure, microhardness and oxidation behaviour. J Alloys Compds 736:236–245 Dzhurinskiy D, Babu A, Pathak P, Elkin A, Dautov S, Shornikov P (2021) Microstructure and wear properties of atmospheric plasma-sprayed Cr3C2-NiCr composite coatings. Surf Coat Technol 428:127904 Reddy NC, Ajay Kumar BS, Ramesh MR, Koppad PG (2018) Microstructure and adhesion strength of Ni 3 Ti coating prepared by mechanical alloying and HVOF. Phys Metals Metallogr 119:462–468 Ghadami F, Zakeri A, Sabour Rouh Aghdam A, Tahmasebi R (2019) Structural characteristics and high-temperature oxidation behavior of HVOF sprayed nano-CeO2 reinforced NiCoCrAlY nanocomposite coatings. Surf Coat Technol 373:7–16 Vasudev H, Thakur L, Bansal A, Singh H, Zafar S (2019) High temperature oxidation and erosion behaviour of HVOF sprayed bi-layer alloy-718/NiCrAlY coating. Surf Coat Technol 362:366–380 Tillmann W, Hagen L, Schaak C, Liß J, Schaper M, Hoyer K-P, Aydinöz ME, Garthe K-U (2020) Adhesion of HVOF-sprayed WC-Co coatings on 316L substrates processed by SLM. J Therm Spray Technol 29:1396–1409 Singh J, Vasudev H, Singh S (2020) Performance of different coating materials against high temperature oxidation in boiler tubes–a review. Mater Today: Proceed 26:972–978 Raza A, Ahmad F, Badri TM, Raza MR, Malik K (2022) An Influence of oxygen flow rate and spray distance on the porosity of HVOF coating and its effects on corrosion—a Review. Materials 15(18):6329 Sabanayagam S, Chockalingam S (2020) Analysis of high temperature oxidation behaviour of SS316 by Al2O3 and Cr2O3 coating. Mater Today: Proceed 33:2641–2645 Sharma V, Kumar S, Kumar M, Deepak D (2020) High temperature oxidation performance of Ni-Cr-Ti and Ni-5Al coatings. Mater Today: Proceed 26:3397–3406 Kumar S, Kumar M, Handa A (2018) Combating hot corrosion of boiler tubes–a study. Eng Fail Anal 94:379–395 Ansari MS, Bansal A, Chawla V, Aggarwal V (2021) Comparative study of hot corrosion behavior of bare and plasma sprayed Al2O3–40% TiO2 coated T-91, A-1 boiler steel and Superfer800H superalloy in Na2SO4–60% V2O5 salt environment. Surface Topogr: Metrol Prop 9(2):025029 Patil VG, Somasundaram B, Kandaiah S, Kumar S (2022) High temperature corrosion behavior of high velocity oxy fuel sprayed NiCrMoFeCoAl-30% SiO2 and NiCrMoFeCoAl-30% Cr2O3 composite coatings on ASTM SA213-T22 steel in a coal-fired boiler environment. Int J Eng 35(7):1416–1427 Madhusudana Reddy G, Durga Prasad C, Patil P, Kakur N, Ramesh MR (2023) Investigation of plasma sprayed NiCrAlY/Cr2O3/YSZ coatings on erosion performance of MDN 420 steel substrate at elevated temperatures. Int J Surf Sci Eng 17(3):180–194. https://doi.org/10.1504/IJSURFSE.2023.10054266 Sharanabasva H, Durga Prasad C, Ramesh MR (2023) Effect of Mo and SiC reinforced NiCr microwave cladding on microstructure, mechanical and wear properties. J Inst Eng Ind Series D. https://doi.org/10.1007/s40033-022-00445-8 Nithin HS, Nishchitha KM, Pradeep DG, Durga Prasad C, Mathapati M (2023) Comparative analysis of CoCrAlY coatings at high temperature oxidation behavior using different reinforcement composition profiles. Weld World 67:585–592. https://doi.org/10.1007/s40194-022-01405-2 Madhusudana Reddy G, Durga Prasad C, Shetty G, Ramesh MR, Nageswara Rao T, Patil P (2022) Investigation of thermally sprayed NiCrAlY/TiO2 and NiCrAlY/Cr2O3/YSZ cermet composite coatings on titanium alloys. Eng Res Exp IOP 4:025049. https://doi.org/10.1088/2631-8695/ac7946 Madhusudana Reddy G, Durga Prasad C, Patil P, Kakur N, Ramesh MR (2022) Elevated temperature erosion performance of plasma sprayed NiCrAlY/TiO2 coating on MDN 420 steel substrate. Surf Topogr: Metrol Prop IOP 10:025010. https://doi.org/10.1088/2051-672X/ac6a6e Madhusudana Reddy G, Durga Prasad C, Shetty G, Ramesh MR, Nageswara Rao T, Patil P (2022) High temperature oxidation behavior of plasma sprayed NiCrAlY/TiO2 & NiCrAlY /Cr2O3/YSZ coatings on titanium alloy. Weld World. https://doi.org/10.1007/s40194-022-01268-7 Naik T, Mahantayya Mathapathi C, Prasad D, Nithin HS, Ramesh MR (2022) Effect of laser post treatment on microstructural and sliding wear behavior of HVOF sprayed NiCrC and NiCrSi coatings. Surf Rev Lett 29(1):225000. https://doi.org/10.1142/S0218625X2250007X Madhusudana Reddy G, Durga Prasad C, Shetty G, Ramesh MR, Nageswara Rao T, Patil P (2021) High temperature oxidation studies of plasma sprayed NiCrAlY/TiO2 & NiCrAlY /Cr2O3/YSZ cermet composite coatings on MDN-420 special steel alloy. Metallogr Microstruct Anal 10:642–651. https://doi.org/10.1007/s13632-021-00784-0 Madhu G, Mrityunjaya Swamy KM, Kumar DA, Durga Prasad C, Harish U (2021) Evaluation of hot corrosion behavior of HVOF thermally sprayed Cr3C2 -35NiCr coating on SS 304 boiler tube steel. Am Inst Phys DOI 10(1063/5):0038279 Prasad CD, Joladarashi S, Ramesh MR, Srinath MS (2020) Microstructure and tribological resistance of flame sprayed CoMoCrSi/WC-CrC-Ni and CoMoCrSi/WC-12Co composite coatings remelted by microwave hybrid heating. J Bio Tribo-Corrosion 6:124. https://doi.org/10.1007/s40735-020-00421-3 Prasad CD, Joladarashi S, Ramesh MR (2020) Comparative investigation of HVOF and flame sprayed CoMoCrSi coating. Am Inst Phys 2247:050004. https://doi.org/10.1063/5.0003883 Prasad CD, Jerri A, Ramesh MR (2020) Characterization and sliding wear behavior of iron based metallic coating deposited by HVOF process on low carbon steel substrate. J Bio Tribo-Corros 6:69. https://doi.org/10.1007/s40735-020-00366-7 Reddy MS, Durga Prasad C, Pradeep Patil MR, Ramesh NR (2021) Hot corrosion behavior of plasma sprayed NiCrAlY/TiO2 and NiCrAlY/Cr2O3/YSZ cermets coatings on alloy steel. Surf Interfaces 22:100810 Prasad CD, Joladarashi S, Ramesh MR, Srinath MS, Channabasappa BH (2020) Comparison of high temperature wear behavior of microwave assisted HVOF sprayed CoMoCrSi-WC-CrC-Ni/WC-12Co composite coatings. SILICON 12:3027–3045. https://doi.org/10.1007/s12633-020-00398-1 Girisha KG, Rakesh R, Durga Prasad C, Sreenivas Rao KV (2015) Development of corrosion resistance coating for AISI 410 grade steel. Appl Mech Mater 813–814:135–139. https://doi.org/10.4028/www.scientific.net/AMM.813-814.135 Prasad CD, Joladarashi S, Ramesh MR, Srinath MS, Channabasappa BH (2019) Development and sliding wear behavior of Co-Mo-Cr-Si cladding through microwave heating. SILICON 11:2975–2986. https://doi.org/10.1007/s12633-019-0084-5 Prasad CD, Joladarashi S, Ramesh MR, Srinath MS, Channabasappa BH (2019) Microstructure and tribological behavior of flame sprayed and microwave fused CoMoCrSi/CoMoCrSi-Cr3C2 coatings. Mater Res Exp, IOP 6:026512. https://doi.org/10.1088/2053-1591/aaebd9 Girisha KG, Sreenivas Rao KV, Durga Prasad C (2018) Slurry erosion resistance of martenistic stainless steel with plasma sprayed Al2O3–40%TiO2 coatings. Mater Today Proceed 5:7388–7393. https://doi.org/10.1016/j.matpr.2017.11.409 Prasad CD, Joladarashi S, Ramesh MR, Srinath MS, Channabasappa BH (2018) Influence of microwave hybrid heating on the sliding wear behaviour of HVOF sprayed CoMoCrSi coating. Mater Res Exp, IOP 5:086519. https://doi.org/10.1088/2053-1591/aad44e Durga Prasad C, Sharnappa Joladarashi MR, Ramesh AS (2018) High Temperature gradient cobalt based clad developed using microwave hybrid heating. Am Inst Phy 1943:020111. https://doi.org/10.1063/1.5029687 Girisha KG, Durga Prasad C, Anil KC, Sreenivas Rao KV (2015) Dry sliding wear behaviour of Al2O3 coatings for AISI 410 grade stainless steel. Appl Mech Mater 766–767:585–589. https://doi.org/10.4028/www.scientific.net/AMM.766-767.585 Fantozzi D, Matikainen V, Uusitalo M, Koivuluoto H, Vuoristo P (2017) Chlorine-induced high temperature corrosion of Inconel 625 sprayed coatings deposited with different thermal spray techniques. Surf Coat Technol 318:233–243 Bansal A, Goyal DK, Singh P, Singla AK, Gupta MK, Bala N, Kolte J, Setia G (2020) Erosive wear behaviour of HVOF-sprayed Ni-20Cr2O3 coating on pipeline materials. Int J Refract Metals Hard Mater 92:105332 Chen L, Lan H, Huang C, Yang B, Lingzhong Du, Zhang W (2017) Hot corrosion behavior of porous nickel-based alloys containing molybdenum in the presence of NaCl at 750° C. Eng Fail Anal 79:245–252 Wei B, Chen C, Jin Xu, Yang L, Jia Y, Yao Du, Guo M, Sun C, Wang Z, Wang F (2022) Comparing the hot corrosion of (100), (210) and (110) Ni-based superalloys exposed to the mixed salt of Na2SO4-NaCl at 750° C: Experimental study and first-principles calculation. Corros Sci 195:109996 Wang J, Li D, Shao T (2022) Hot corrosion and electrochemical behavior of NiCrAlY, NiCoCrAlY and NiCoCrAlYTa coatings in molten NaCl-Na2SO4 at 800° C. Surf Coat Technol 440:128503 Chen L, Zhang X, Yue Wu, Chen C, Li Y, Zhou W, Ren X (2022) Effect of surface morphology and microstructure on the hot corrosion behavior of TiC/IN625 coatings prepared by extreme high-speed laser cladding. Corros Sci 201:110271 Hasegawa M, Hirata K, Dlouhý I (2019) Microstructural change and fracture behavior under different heat exposure conditions on thermal barrier coatings deposited on tial intermetallic compound. Key Eng Mater 810:27–33 Kaplan M, Uyaner M, Ozgurluk Y, Doleker KM, Karaoglanli AC (2019) Evaluation of hot corrosion behavior of APS and HVOF sprayed thermal barrier coatings (TBCs) exposed to molten Na2SO4+ V2O5 salt at 1000 C. Eng Des Appl. https://doi.org/10.1007/978-3-319-79005-3_28 Wei Z, Yuping Wu, Hong S, Cheng J, Qiao L, Cheng J, Zhu S (2021) Ultrasonic cavitation erosion behaviors of high-velocity oxygen-fuel (HVOF) sprayed AlCoCrFeNi high-entropy alloy coating in different solutions. Surf Coat Technol 409:126899 Muthu SM, Arivarasu M, Arivazhagan N (2019) Investigation of hot corrosion resistance of bare and Ni-20% Cr coated superalloy 825 to Na2SO4-60% V2O5 environment at 900° C. Proced Struct Integr 14:290–303 Hao E, An Y, Zhao X, Zhou H, Chen J (2018) NiCoCrAlYTa coatings on nickel-base superalloy substrate: deposition by high velocity oxy-fuel spraying as well as investigation of mechanical properties and wear resistance in relation to heat-treatment duration. Appl Surf Sci 462:194–206 Somasundaram B, Navinesh BC, Jegadeeswaran N (2021) Erosion behaviour of HVOF sprayed WC. Co-NiCrAlYSi (35%-65%) coatings. Mater Today: Proceed 45:372–376 Ramkumar KD, Abraham WS, Viyash V, Arivazhagan N, Rabel AM (2017) Investigations on the microstructure, tensile strength and high temperature corrosion behaviour of Inconel 625 and Inconel 718 dissimilar joints. J Manuf Process 25:306–322 Zhang G, Sun Y, Gao H, Zuo D, Liu Xu (2021) A theoretical and experimental investigation of particle embedding and erosion behaviour of PDMS in micro-abrasive air-jet machining. Wear 486:204118 Chen L, Zhao Yu, Guan C, Tianbiao Yu (2021) Effects of CeO2 addition on microstructure and properties of ceramics reinforced Fe-based coatings by laser cladding. Int J Adv Manuf Technol 115:2581–2593 Alok V, Kumar A, Patnaik A, Meena ML (2021) Influence of deposition parameters on tribological performance of HVOF coating: a review. Materials science and engineering. IOP Publishing, Bristol, p 012015 Sharma AK, Perumal G, Arora HS, Grewal HS (2021) Slurry erosion-corrosion resistance of MoNbTaTiZr high entropy alloy. J Bio-Tribo-Corros 7:1–10 Xu J, Peng S, Li Z, Jiang S, Xie Z-H, Munroe P, Hong Lu (2021) Remarkable cavitation erosion–corrosion resistance of CoCrFeNiTiMo high-entropy alloy coatings. Corros Sci 190:109663 Ozgurluk Y, Gulec A, Ozkan D, Binal G, Karaoglanli AC (2023) Structural characteristics, oxidation performance and failure mechanism of thermal barrier coatings fabricated by atmospheric plasma spraying and detonation gun spraying. Eng Fail Anal 152:107499 Yuan K, Zhu J, Dong W, Yueguang Yu, Xiaoliang Lu, Ji X, Wang X (2017) Applying low-pressure plasma spray (LPPS) for coatings in low-temperature SOFC. Int J Hydrogen Energy 42(34):22243–22249 Kumar R, Kumar R, Kumar S (2018) Erosion corrosion study of HVOF sprayed thermal sprayed coating on boiler tubes: a review. IJSMS. https://doi.org/10.51386/25815946/ijsms-v1i3p101 Abhijith NV, Kumar D, Kalyansundaram D (2022) Development of single-stage TiNbMoMnFe high-entropy alloy coating on 304L stainless steel using HVOF thermal spray. J Therm Spray Technol 31(4):1032–1044 Azizpour MJ, Tolouei-Rad M (2019) The effect of spraying temperature on the corrosion and wear behavior of HVOF thermal sprayed WC-Co coatings. Ceram Int 45(11):13934–13941 Silveira LL, Pukasiewicz AGM, de Aguiar DJM, Zara AJ, Björklund S (2019) Study of the corrosion and cavitation resistance of HVOF and HVAF FeCrMnSiNi and FeCrMnSiB coatings. Surf Coat Technol 374:910–922 Ghadami F, Sabour Rouh Aghdam A, Ghadami S (2020) Mechanism of the oxide scale formation in thermally-sprayed NiCoCrAlY coatings modified by CeO2 nanoparticles. Mater Today Commun 24:101357 Upadhyaya R, Tailor S, Shrivastava S, Modi SC (2018) High performance thermal-sprayed WC-10Co-4Cr coatings in narrow and complex areas. Surf Eng 34(5):412–421 Anand Babu K, Jegadeeswaran N, Nithin HS, Kapilan N (2021) Studies on solid particle erosion by HVOF sprayed 25%(Cr3C2-25 (Ni20Cr))+ 75% NiCrAlY on Ti-31. Mater Today: Proceed 45:246–253 Ghadami F, Sabour Rouh Aghdam A, Ghadami S (2020) Isothermal and cyclic oxidation behavior of HVOF-Sprayed NiCoCrAlY coatings: comparative investigations on the conventional and nanostructured coatings. J Therm Spray Technol 29:1926–1942 Lynam A, Rincon Romero A, Xu F, Wellman RW, Hussain T (2022) Thermal spraying of ultra-high temperature ceramics: a review on processing routes and performance. J Therm Spray Technol 31(4):745–779 Chen Y, Yuping Wu, Hong S, Long W, Ji X (2020) The effect of impingement angle on erosion wear characteristics of HVOF sprayed WC-Ni and WC-Cr3C2-Ni cermet composite coatings. Mater Res Exp 7(2):026503 Thermsuk S, Surin P (2019) Optimization parameters of WC-12Co HVOF sprayed coatings on SUS 400 stainless steel. Proced Manuf 30:506–513 Ding X, Cheng X-D, Shi J, Li C, Yuan C-Q, Ding Z-X (2018) Influence of WC size and HVOF process on erosion wear performance of WC-10Co4Cr coatings. Int J Adv Manuf Technol 96:1615–1624 Matikainen V, Rubio Peregrina S, Ojala N, Koivuluoto H, Schubert J, Houdková Š, Vuoristo P (2019) Erosion wear performance of WC-10Co4Cr and Cr3C2–25NiCr coatings sprayed with high-velocity thermal spray processes. Surf Coat Technol 370:196–212 Qadir D, Sharif R, Nasir R, Awad A, Mannan HA (2023) A review on coatings through thermal spraying. Chem Papers. https://doi.org/10.1007/s11696-023-03089-4 López-Ortega A, Arana JL, Rodríguez E, Bayón R (2018) Corrosion, wear and tribocorrosion performance of a thermally sprayed aluminum coating modified by plasma electrolytic oxidation technique for offshore submerged components protection. Corros Sci 143:258–280 Meghwal A, Ameey Anupam BS, Murty CC, Berndt RS, Kottada AS, Ang M (2020) Thermal spray high-entropy alloy coatings: a review. J Therm Spray Technol 29:857–893 Zhao W, Kong D (2019) Effects of laser power on immersion corrosion and electrochemical corrosion performances of laser thermal sprayed amorphous AlFeSi coatings. Appl Surf Sci 481:161–173 Wood RJK, Herd S, Thakare MR (2018) A critical review of the tribocorrosion of cemented and thermal sprayed tungsten carbide. Tribol Int 119:491–509 Ozgurluk Y, Doleker KM, Karaoglanli AC (2018) Hot corrosion behavior of YSZ, Gd2Zr2O7 and YSZ/Gd2Zr2O7 thermal barrier coatings exposed to molten sulfate and vanadate salt. Appl Surf Sci 438:96–113 Guo L, Zhang C, Li M, Sun W, Zhang Z, Ye F (2017) Hot corrosion evaluation of Gd2O3-Yb2O3 co-doped Y2O3 stabilized ZrO2 thermal barrier oxides exposed to Na2SO4+ V2O5 molten salt. Ceram Int 43(2):2780–2785 Prasad CD, Kollur S, Aprameya CR, Chandramouli TV, Jagadeesha T, Prashanth BN (2023) Investigations on tribological and microstructure characteristics of WC-12Co/FeNiCrMo composite coating by HVOF process. JOM J Miner, Metals Mater Soc (TMS). https://doi.org/10.1007/s11837-023-06242-2 Durga Prasad C, Kollur S, Nusrathulla M, Satheesh Babu G, Hanamantraygouda MB, Prashanth BN, Nagabhushana N (2023) Characterisation and wear behaviour of SiC reinforced FeNiCrMo composite coating by HVOF process. Trans IMF. https://doi.org/10.1080/00202967.2023.2246259 Sharanabasava H, Raviprakash M, Durga Prasad C, Ramesh MR, Phanibhushana MV, Vasudev H, Kumar S (2023) Microstructure, mechanical and wear properties of SiC and Mo reinforced NiCr microwave cladding. Adv Mater Process Technol. https://doi.org/10.1080/2374068X.2023.2257937 Madhu Sudana Reddy G, Durga Prasad C, Kollur S, Avinash Lakshmikanthan R, Suresh ACR (2023) Investigation of high temperature erosion behaviour of NiCrAlY/TiO2 plasma coatings on titanium substrate. JOM J Miner Metals Mater Soc (TMS). https://doi.org/10.1007/s11837-023-05894-4 Madhusudana Reddy G, Durga Prasad C, Patil P, Kakur N, Ramesh MR (2023) High Temperature erosion performance of NiCrAlY/Cr2O3/YSZ plasma spray coatings. Trans IMF. https://doi.org/10.1080/00202967.2023.2208899 Sharanabasva H, Durga Prasad C, Ramesh MR (2023) Characterization and wear behavior of nicrmosi microwave cladding. J Mater Eng Perform. https://doi.org/10.1007/s11665-023-07998-z Vishnoi M, Murtaza Q, Kumar P (2021) Effect of rare earth elements on coatings developed by thermal spraying processes (TSP)–a brief review. Mater Today: Proceed 44:4053–4058 Kumar S, Kumar M, Handa A (2020) Erosion corrosion behaviour and mechanical properties of wire arc sprayed Ni-Cr and Ni-Al coating on boiler steels in a real boiler environment. Mater High Temp 37(6):370–384 Milan Shahana S, Srinivasa Rao B, Kamaraj M (2022) High-temperature oxidation and hot corrosion of thermal spray coatings. A treatise on corrosion science, engineering and technology. Springer Nature Singapore, Singapore, pp 407–420 Doolabi DS, Rahimipour MR, Alizadeh M, Pouladi S, Hadavi SMM, Vaezi MR (2017) Effect of high vacuum heat treatment on microstructure and cyclic oxidation resistance of HVOF-CoNiCrAlY coatings. Vacuum 135:22–33 Patel SK, Singh VP, Kuriachen B (2019) Friction stir processing of alloys with secondary phase particles: an overview. Mater Manuf Process 34(13):1429–1457 Ludwig GA, Malfatti CF, Schroeder RM, Ferrari VZ, Muller IL (2019) WC10Co4Cr coatings deposited by HVOF on martensitic stainless steel for use in hydraulic turbines: resistance to corrosion and slurry erosion. Surf Coat Technol 377:124918 Mago J, Bansal S, Gupta D, Jain V (2021) Influence of microwave heating on metallurgical and mechanical properties of Ni-40Cr3C2 composite clads in the context of cavitation erosion resistance characteristics. Proc Inst Mech Eng C J Mech Eng Sci 235(7):1258–1276 Berger JE, Schulz R, Savoie S, Gallego J, Kiminami CS, Bolfarini C, Botta WJ (2017) Wear and corrosion properties of HVOF coatings from Super duplex alloy modified with addition of boron. Surf Coat Technol 309:911–919