Tool life and cutting forces in end milling Inconel 718 under dry and minimum quantity cooling lubrication cutting conditions

Aznijar, 2010, A review of cryogenic cooling in high speed machining (HSM) of mold and die steels, Sci. Res. Essays, 5, 412 Choudhury, 1998, Machinability of nickel-base super alloys: a general review, J. Mater. Process. Technol., 77, 278, 10.1016/S0924-0136(97)00429-9 Devillez, 2007, Cutting forces and wear in dry machining of Inconel 718 with coated carbide tools, Wear, 262, 931, 10.1016/j.wear.2006.10.009 Dhar, 2007, Effect of minimum quantity lubrication (MQL) on tool wear, surface roughness and dimensional deviation in turning AISI-4340 steel, G. U. J. Sci., 20, 23 Ezugwu, 1999, The machinability of nickel based alloys: a review, J. Mater. Process. Technol., 86, 1, 10.1016/S0924-0136(98)00314-8 Ezugwu, 2005, Key improvements in the machining of difficult-to-machine aerospace superalloys, Int. J. Mach. Tools Manuf., 45, 1353, 10.1016/j.ijmachtools.2005.02.003 Fratila, 2009, Evaluation of near-dry machining effects on gear milling process efficiency, J. Clean. Prod., 17, 839, 10.1016/j.jclepro.2008.12.010 Fratila, 2011, Application of Taguchi method to selection of optimal lubrication and cutting conditions in face milling of AlMg3, J. Clean. Prod., 19, 640, 10.1016/j.jclepro.2010.12.007 International Standard Organization, 1989 Jeong, 2002 Kamata, 2007, High speed MQL finish-turning of Inconel 718 with different coated tools, J. Mater. Process. Technol., 192–193, 281, 10.1016/j.jmatprotec.2007.04.052 Kitagawa, 1997, Temperature and wear of cutting tools in high-speed machining of Inconel 718 and Ti-6Al-6V-2Sn, Wear, 202, 142, 10.1016/S0043-1648(96)07255-9 Klocke, 1997, Dry cutting, CIRP Ann., 46, 519, 10.1016/S0007-8506(07)60877-4 Lalwani, 2008, Experimental investigations of cutting parameters influence on cutting forces and surface roughness in finish hard turning of MDN250 steel, J. Mater. Process. Technol., 206, 167, 10.1016/j.jmatprotec.2007.12.018 Li, 2006, An experimental study of tool wear and cutting force variation in the end milling of Inconel 718 with coated carbide inserts, J. Mater. Process. Technol., 180, 296, 10.1016/j.jmatprotec.2006.07.009 Liao, 2007, Feasibility study of the minimum quantity lubrication in high-speed end milling of NAK80 hardened steel by coated carbide tool, Int. J. Mach. Tools Manuf., 47, 1667, 10.1016/j.ijmachtools.2007.01.005 Liao, 2008, Behaviors of end milling Inconel 718 superalloy by cemented carbide tools, J. Mater. Process. Technol., 201, 460, 10.1016/j.jmatprotec.2007.11.176 Obikawa, 2006, High speed grooving with applying MQL, Int. J. Mach. Tools Manuf., 46, 1854, 10.1016/j.ijmachtools.2005.11.007 Obikawa, 2008, Micro-liter lubrication machining of Inconel 718, Int. J. Mach. Tools Manuf., 48, 1605, 10.1016/j.ijmachtools.2008.07.011 Pawade, 2011, Multi-objective optimization of surface roughness and cutting forces in high-speed turning of Inconel 718 using Taguchi grey relational analysis (TGRA), Int. J. Adv. Manuf. Technol., 56, 47, 10.1007/s00170-011-3183-z Sanchez, 2010, Machining evaluation of a hybrid MQL-CO2 grinding technology, J. Clean. Prod., 18, 1840, 10.1016/j.jclepro.2010.07.002 Settineri, 2008, Properties and performances of innovative coated tools for turning inconel, Int. J. Mach. Tools Manuf., 48, 815, 10.1016/j.ijmachtools.2007.12.007 Shashidhara, 2010, Vegetable oils as a potential cutting fluid – An evolution, Tribol. Int., 43, 1073, 10.1016/j.triboint.2009.12.065 Sokovic, 2001, Ecological aspects of the cutting fluids and its influence on quantifiable parameters of the cutting processes, J. Mater. Process. Technol., 109, 181, 10.1016/S0924-0136(00)00794-9 Tseng, 2002, The intelligent on-line monitoring of end milling, Int. J. Mach. Tools Manuf., 42, 89, 10.1016/S0890-6955(01)00091-8 Vagnorius, 2011, Effect of high-pressure cooling on life of SiAlON tools in machining of Inconel 718, Int. J. Adv. Manuf. Technol., 54, 83, 10.1007/s00170-010-2944-4 Wang, 2003, The effect of tool flank wear on the orthogonal cutting process and its practical implications, J. Mater. Process. Technol., 142, 338, 10.1016/S0924-0136(03)00604-6 Weinert, 2004, Dry machining and minimum quantity lubrication, CIRP Ann. Manuf. Technol., 53, 511, 10.1016/S0007-8506(07)60027-4