Conjugate heat transfer on full-coverage film cooling with array jet impingements with various Biot numbers

Experimental Thermal and Fluid Science - Tập 83 - Trang 1-8 - 2017
Eui Yeop Jung1, Heeyoon Chung1, Seok Min Choi1, Ta-kwan Woo2, Hyung Hee Cho1
1Department of Mechanical Engineering, Yonsei University, 50, Sedamun-gu, Seoul 120-749, Republic of Korea
2SUNG IL Co. LTD., Busan 1587-4, Republic of Korea

Tài liệu tham khảo

Metzger, 1973, Effectiveness and heat transfer with full-coverage film cooling, J. Eng. Power, 95, 180, 10.1115/1.3445720 Andrews, 1988, Small diameter film cooling holes: the influence of hole size and pitch, Int. J. Turbo Jet Eng., 5, 61 G.E. Andrews, F.B. Teherani, Small Diameter Film Cooling Hole Heat Transfer: The Influence of the Number of Holes, ASME 89-GT-7, 1989. Crawford, 1980, Full-coverage film cooling part I: comparison of heat transfer data for three injection angles, J. Eng. Power, 102, 1000, 10.1115/1.3230334 Nasir, 2001, Effect of compound angle injection on flat surface film cooling with large streamwise injection angle, Exp. Therm. Fluid Sci., 25, 23, 10.1016/S0894-1777(01)00052-8 Yang, 2012, Experimental investigation on film cooling characteristics from a row of holes with ridge-shaped tabs, Exp. Therm. Fluid Sci., 37, 113, 10.1016/j.expthermflusci.2011.10.011 Cho, 1995, Heat (mass) transfer and film cooling effectiveness with injection through discrete holes: part I – within holes and on the back surface, J. Turbomach., 117, 440, 10.1115/1.2835680 Cho, 1995, Heat (mass) transfer and film cooling effectiveness with injection through discrete holes: part II – on the exposed surface, J. Turbomach., 117, 451, 10.1115/1.2835681 Cho, 1997, Total-coverage discrete hole wall cooling, J. Turbomach., 119, 320, 10.1115/1.2841115 Cho, 2001, Local heat/mass transfer measurement on the effusion plate in impingement/effusion cooling system, J. Turbomach., 123, 601, 10.1115/1.1344904 Rhee, 2003, Heat (mass) transfer on effusion plate in impingement/effusion cooling systems, J. Thermophys. Heat Transf., 17, 95, 10.2514/2.6739 S. Dhiman, S. Yavuzkurt, Film Cooling Calculations with an Iterative Conjugate Heat Transfer Approach Using Empirical Heat Transfer Coefficient Corrections, ASME GT2010-22958. Panda, 2014, Conjugate heat transfer from an impingement and film-cooled flat plate, J. Thermophys. Heat Transf., 28, 647, 10.2514/1.T4119 C. Zhang, J. Liu, Z. Wang, B. An, The Effects of Biot Number on the Conjugate Film Cooling Effectiveness under Different Blowing Ratio, ASME GT2013-94041. Caciolli, 2013, Comparison between PSP and TLC steady state techniques for adiabatic effectiveness measurement on a multiperforated plate, Exp. Therm. Fluid Sci., 48, 122, 10.1016/j.expthermflusci.2013.02.015 J.W. McClintic, Experimental Investigation of Overall Effectiveness and Coolant Jet Interactions on a Fully Cooled C3X Turbine Vane, M.S. Thesis, The University of Texas At Austin, 2013. T.E. Dyson, J.W. McClintic, D.G. Bogard, S.D. Bradshaw, Adiabatic and Overall Effectiveness for a Fully Cooled Turbine Vane, ASME GT2013-94928. E.Y. Jung, H. Chung, S.M. Choi, T. Woo, H.H. Cho, Conjugate Heat Transfer on Full-Coverage Film Cooling with Array Impingement Jets, ASME GT2015-43810. K.L. Harrsion, D. Bogard, Use of Adiabatic Wall Temperature in Film Cooling To Predict Wall Heat Flux and Temperature, ASME GT2008-51424. Ammari, 1990, The effect of density ratio on the heat transfer coefficient from a film-cooled flat plate, J. Turbomach., 112, 444, 10.1115/1.2927679 Moffat, 1988, Describing the uncertainties in experimental results, Exp. Therm. Fluid Sci., 1, 3, 10.1016/0894-1777(88)90043-X Harrington, 2001, Full-coverage film cooling with short normal injection holes, J. Turbomach., 123, 798, 10.1115/1.1400111 Scittore, 2007, Investigation of velocity profiles for effusion cooling of a combustor liner, J. Turbomach., 129, 518, 10.1115/1.2720492 Rhee, 2003, Local heat/mass transfer and flow characteristics of array impinging jets with effusion holes ejecting spent air, Int. J. Heat Mass Transf., 46, 1049, 10.1016/S0017-9310(02)00363-0 Wilfert, 1996, The aerodynamic mixing effect of discrete cooling jets with mainstream flow on a highly loaded turbine blade, J. Turbomach., 118, 468, 10.1115/1.2836692 Shinn, 2013, Large Eddy simulations of film-cooling flows with a micro-ramp vortex generator, J. Turbomach., 135, 011004, 10.1115/1.4006329 Yeun, 2005, Film cooling characteristics of rows of round holes at various streamwise angles in a crossflow: part I. Effectiveness, Int. J. Heat Mass Transf., 48, 4995, 10.1016/j.ijheatmasstransfer.2005.05.019