Internal and external cooling of a full coverage effusion cooling plate: Effects of double wall configuration and conditions

Rogers, N., Ren, Z., Buzzard, W., Sweeney, B., Tinker, N., Ligrani, P. M., Hollingsworth, K. D., Liberatore, F., Patel, R., Ho, S., and Moon, H.-K., Effects of Double Wall Cooling Configuration and Conditions on Performance of Full Coverage Effusion Cooling, Paper Number GT2016-56515, ASME TURBO EXPO 2016: Turbomachinery Technical Conference and Exposition, Seoul, South Korea, June 13-17, 2016. Sasaki, 1979, Film cooling effectiveness for injection from multirow holes, ASME Trans - J Eng Power, 101, 101, 10.1115/1.3446430 Martiny, 1995, Full-coverage film cooling investigation: adiabatic wall temperatures and flow visualization Schulz, 2001, Combustor liner cooling technology in scope of reduced pollulant formation and rising thermal efficiencies, vol 934, 135 Kelly, 2003, An investigation of the heat transfer for full coverage film cooling Krewinkel, 2013, A review of gas turbine effusion cooling studies, Int J Heat Mass Transf, 66, 706, 10.1016/j.ijheatmasstransfer.2013.07.071 Andrews, 1986, Transpiration cooling: contributions of film cooling to the overall cooling effectiveness Al Dabagh, 1990, Impingement/effusion cooling: the influence of the number of impingement holes and pressure loss on the heat transfer coefficient, ASME Trans - J Turbomach, 112, 467, 10.1115/1.2927682 Cho, 2001, Local heat/mass transfer measurement on the effusion plate in impingement/effusion cooling systems, ASME Trans. J. Turbomach, 123, 601, 10.1115/1.1344904 Bailey, 2002, Experimental and numerical study of heat transfer in a gas turbine combustor liner, ASME Trans – J Eng Gas Turbines Power, 125, 994, 10.1115/1.1615256 Lin, 2003, Investigation of film cooling effectiveness of full-coverage inclined multihole walls with different hole arrangements Scrittore, 2007, Investigation of velocity profiles for effusion cooling of a combustor liner, ASME Trans - J Turbomach, 129, 518, 10.1115/1.2720492 Stoakes, 2011, Optimized impingement configurations for double wall cooling applications King, 2009, Simulation of synthetic jets with non-sinusoidal forcing functions for heat transfer applications Kumar, 2013, Numerical simulations of heat transfer distribution of a two-pass square channel with V-Rib turbulator and bleed holes, J Heat Mass Transf, 49, 1141, 10.1007/s00231-013-1156-5 Shevchuk, 2006, Unsteady conjugate laminar heat transfer of a rotating non-uniformly heated disk: application to the transient experimental technique, Int J Heat Mass Transf, 49 Ren, Z., Vanga, S. R., Rogers, N., Ligrani, P. M., Hollingsworth, K. D., Liberatore, F., Patel, R., Srinivasan, R., and Ho, Y., Internal and External Cooling of a Full Coverage Effusion Cooling Plate: Effects of Double Wall Cooling Configuration and Conditions, Paper Number GT2017-64921, ASME TURBO EXPO 2017: Turbomachinery Technical Conference and Exposition, Charlotte, North Carolina, USA, June 26-30, 2017. Hay, 1998, Calibration of micro-encapsulated liquid crystals using hue angle and a dimensionless temperature, Exp Therm Fluid Sci, 18, 251, 10.1016/S0894-1777(98)10026-2 Kline, 1953, Describing uncertainties in single sample experiments, Mech Eng, 75, 3 Moffat, 1988, Describing the uncertainties in experimental results, Exp Therm Fluid Sci, 1, 3, 10.1016/0894-1777(88)90043-X