Investigations of flank wear, cutting force, and surface roughness in the machining of Al-6061–TiB2 in situ metal matrix composites produced by flux-assisted synthesis

Allision JE, Gole GS (1993) Metal-matrix composites in the automotive industry: opportunities and challenges. J Min Met Mater Sci 45:19–24

Kuruvilla AK et al (1990) Sripta Metall 24:873

Ma ZY et al (1994) Scripta Metall 31:635

Daniel BS, Murthy VS, Murty GS (1997) Metal-ceramic composites via in-situ methods. J Mater Process Technol 68:132–155

Tjong SC, Ma ZY (2000) Micro structural and mechanical characteristics of in- situ metal matrix composites. Mater Sci Eng R 29:49–113

Lakshmi S, Lu L, Gupta M (1998) In-situ preparation of TiB2 reinforced Al based composites. J Mater Process Technol 73:160–166

Fan T, Yang G, Zhang D (2005) Thermodynamic effect of alloying addition on in-situ reinforced TiB2/Al composites. Metall Mater Trans A 36:225–233

Zhao D, Liu X, LiuY BX (2005) In-situ preparation of Al matrix composites reinforced by TiB2 particles and sub-micron ZrB2. J Mater Sci 40:4365–4368

Christy TV, Murugan N, Kumar S (2010) A comparative study on the microstructures and mechanical properties of Al 6061 Alloy and the MMC Al 6061/TiB2/12P. J Min Mater Charact Eng 9:57–65

Ozcatalbas Y (2003) Chip and built-up edge formation in the machining of in-situ Al4C3–Al composite. Mater Des 24:215–221

Ozcatalbas Y (2003) Investigation of the machinability behavior of Al4C3 reinforced Al-based composite produced by mechanical alloying technique. Comp Sci Technol 63:53–61

Manna A, Bhattacharyya B (2003) A study on machinability of Al/SiC–MMC. J Mater Process Technol 140:711–716

Manna A, Bhattacharyya B (2005) Influence of machining parameters on the machinability of particulate reinforced Al/SiC–MMC. Int J Adv Manuf Technol 25:850–856

Quan YM, Zhou ZH, Ye BY (1999) Cutting process and chip appearance of aluminum matrix composites reinforced by SiC particle. J Mater Process Technol 91:231–235

Ozben T, Kilickap E, Çakır O (2008) Investigation of mechanical and machinability properties of SiC particle reinforced Al–MMC. J Mater Process Technol 198:220–225

Muthukrishnan N, Murugan M, Prahladarao K (2008) An investigation on the machinability of Al–Sic metal matrix composites using PCD insert. Int J Adv Manuf Technol 38:447–454

Muthukrishnan N, Murugan M, Prahladarao K (2008) Machinability issues in turning of Al–Sic (10p) metal matrix composites. Int J Adv Manuf Technol 39:211–218

Lin JT, Bhattacharyya D, Lane C (1995) Machinability of a silicon carbide reinforced aluminum metal matrix composite. Wear 183(2):883–888

Pramanik A, Zhang LC, Arsecularatne JA (2008) Machining of metal matrix composites: effect of ceramic particles on residual stress surface roughness and chip formation. Int J Mach Tools Manuf 48:1613–1625