3D EBSD characterization of deformation structures in commercial purity aluminum

Adams, 1993, Orientation imaging — the emergence of a new microscopy, Metall Trans A, 24, 819, 10.1007/BF02656503 Wright, 1993, A review of automated orientation imaging microscopy(OIM), J Comput Assist Microsc, 5, 207 Schwarzer, 1997, Automated crystal lattice orientation mapping using a computer-controlled SEM, Micron, 28, 249, 10.1016/S0968-4328(97)00010-3 Delannay, 2001, Quantitative analysis of grain subdivision in cold rolled aluminium, Acta Mater, 49, 2441, 10.1016/S1359-6454(01)00150-1 Humphreys, 2001, Review — grain and subgrain characterisation by electron backscatter diffraction, J Mater Sci, 36, 3833, 10.1023/A:1017973432592 Dehoff, 1983, Quantitative serial sectioning analysis — preview, J Microsc-Oxford, 131, 259, 10.1111/j.1365-2818.1983.tb04254.x Poulsen, 2001, Three-dimensional maps of grain boundaries and the stress state of individual grains in polycrystals and powders, J Appl Crystallogr, 34, 751, 10.1107/S0021889801014273 Nielsen, 2000, A three-dimensional X-ray diffraction microscope for deformation studies of polycrystals, Mater Sci Eng A-Struct, 319, 179 Schmidt, 2008, Direct observation of 3-D grain growth in Al-0.1% Mn, Scr Mater, 59, 491, 10.1016/j.scriptamat.2008.04.049 West, 2009, Direct non-destructive observation of bulk nucleation in 30% deformed aluminum, Scr Mater, 61, 875, 10.1016/j.scriptamat.2009.07.027 Kral, 2000, Three-dimensional analysis of microstructures, Mater Charact, 45, 17, 10.1016/S1044-5803(00)00046-2 Alkemper, 2001, Three-dimensional characterization of dendritic microstructures, Acta Mater, 49, 897, 10.1016/S1359-6454(00)00355-4 Li, 1998, Serial sectioning method in the construction of 3-D microstructures for particle-reinforced MMCs, Mater Charact, 41, 81, 10.1016/S1044-5803(98)00023-0 Spowart, 2006, Automated serial sectioning for 3-D analysis of microstructures, Scr Mater, 55, 5, 10.1016/j.scriptamat.2006.01.019 Groeber, 2006, 3D reconstruction and characterization of polycrystalline microstructures using a FIB-SEM system, Mater Charact, 57, 259, 10.1016/j.matchar.2006.01.019 Zaefferer, 2008, Three-dimensional orientation microscopy in a focused ion beam-scanning electron microscope: a new dimension of microstructure characterization, Metall Mater Trans A, 39A, 374, 10.1007/s11661-007-9418-9 Mishin, 2004, The effect of roll gap geometry on microstructure in cold-rolled aluminum, Acta Mater, 52, 5761, 10.1016/j.actamat.2004.08.028 Lewis, 2006, Two- and three-dimensional microstructural characterization of a super-austenitic stainless steel, Mat Sci Eng A-Struct, 418, 11, 10.1016/j.msea.2005.09.088 Wall, 2001, A high-resolution serial sectioning specimen preparation technique for application to electron backscatter diffraction, Ultramicroscopy, 88, 73, 10.1016/S0304-3991(01)00071-7 Rollett, 2007, Three-dimensional characterization of microstructure by electron back-scatter diffraction, Annu Rev Mater Res, 37, 627, 10.1146/annurev.matsci.37.052506.084401 Lin FX, Godfrey A, Winther G, Juul Jensen D. Alignment of serial sections for 3D microstructure characterization of cold rolled aluminum by EBSD. Proc 31th Risø Int Symp Mater Sci 2010;303–10.